Home Motivation Vocabulary Air Conditioner

Vocabulary Air Conditioner

SHARE
Vocabulary Air Conditioner English Language Lessons
Vocabulary Air Conditioner English Language Lessons
Submit your resume Get Your Dream Job Anywhere

As with anything technical, air conditioning involves a fair bit of specialised terminology. If you’ve been looking for a unit or talking to a repairman, you may have found yourself wondering what on earth it all means! With this in mind, we’ve compiled a glossary of the most commonly used words, phrases and terms that crop up when you’re talking air conditioning. Brush up on these terms and you’ll find it much easier to understand what can seem like a foreign language.

HVAC. Heating, ventilation and air conditioning. This acronym refers to the entire discipline that surrounds air conditioning

TAMS Studies Aligarh Learn English Make Good Future
TAMS Studies Aligarh Learn English Make Good Future

ARC. Australian Refrigeration Council: the body that is responsible for granting refrigeration handling licenses to approved technicians in Australia. When a technician is approved, they’re said to have the ‘ARC TICK’.

Split System. Now one of the most popular types of air conditioning systems used in homes, a split system is ‘split’ into two units: one that’s inside, and one that’s outside. Relatively easy to install (as no ductwork is required), these systems are known for being quiet and energy-efficient.

Outdoor Unit. This is the part of an air conditioning system that contains the compressor, propeller fan, circuit board and heat exchange coil. It’s situated outside and pumps refrigerant to and from its companion indoor unit. You’ll often hear this unit referred to as the ‘condenser’ or ‘heat exchanger’.

Indoor Unit. The part of an air conditioning unit that’s located within the home, and provides the ‘conditioned’ air into space. This unit contains a heat exchange coil, filters, remote signal receiver and fan.

Multi-split system. This is a split system where there’s more than one indoor unit attached to a single outdoor unit. The beauty of a multi-split system is that you can use it to heat or cool different areas of the house independently – or even maintain an even temperature in one large area by using two units. Such systems operate in either heating or cooling at one time.

Ducted system. Ducted systems include an internal fan coil installed into the roof space of a house. From this central location, a series of ducts are installed in multiple locations throughout the house, allowing you to heat and cool different areas of the home easily. This provides discreet air-conditioned comfort as the only visible components are the return air grilles, discharge grilles and controller.

Hydronic system. This is a typical heating and cooling system that uses ‘liquid heat transfer’ – in other words, heating up water and moving it through pipes installed under the floor.

Heating/cooling capacity. The capacity output figure indicates the amount of heating/cooling the unit can produce.

Air filter. Air filters are designed to trap dust and contaminants in the air from clogging up the indoor unit of an air conditioning system. They are manufactured from thermally bonded polyester fibre or a plastic resin-based net.

Air purifier. This product is specifically designed to remove allergens, pollutants, bacteria and odours from the air in your home. Some air purifiers can be integrated into existing air conditioning systems, while others are portable units.

Thermostat. You’ll probably be familiar with this one: simply, it’s the device that controls the temperature inside your home. Most thermostats consist of a sensor that monitors air temperature and relays this information to the air conditioning unit – enabling it to effectively heat or cool the space.

Zoning. This is a method of heating or cooling different areas (or rooms) within one house independently – usually by using separate controls, or by opening and closing dampers within ducts in each zone.

Heat pump. Another term for a reverse cycle air conditioner which can heat and cool indoor spaces. There are three main types: air-to-air, water source and geothermal. Heat pumps are popular for those living in climates with moderate heating and cooling needs.

Duct. This is a tube that carries air from a central fan coil to various areas of a house. Ducts can be round or rectangular and are made from a variety of materials including sheet metal, fibreglass and vinyl.

Commissioning. The final step in installing an air-con system! It involves a technician checking and testing every component in the system to make sure it all complies with technical codes and manufacturers standards. Once commissioning is completed, the system is ready to go.

Inverter technology. An inverter works like the accelerator of a car, gently increasing/decreasing power. Inverter based systems can achieve the desired room temperature quicker and steadily without fluctuations which means uninterrupted comfort and savings in running costs.

R410A. A non-ozone depleting refrigerant or fluid that transfers heat energy between the indoor and outdoor units of the air conditioning system.

R-32. A successor to the R-410A refrigerant, R-32 is also non-ozone depleting and has 66% lower global warming potential (GWP) factor than R-410A.

Is there a term you’ve heard that we haven’t included? Get in touch and we will add it to our glossary.

Find the Top 100 AC Maintenance Services Near Me

Submit your resume Get Your Dream Job Anywhere